午夜时分性爱大放送网站,久久免费人成视频观看,国内熟女啪啪自拍,久久无码高潮喷水办公室,午夜a男人的天堂京东热,在线日本高清不卡免费v,久久综合无码中文字幕

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

electric furnace hydraulic cylinder Sold to El Salvador

Release time:2023-11-12 15:32:25 Hits: Current position: Home > News

This article mainly introduces:

El Salvador hydraulic cylinder,electric furnace hydraulic cylinder manufacturer,electric furnace hydraulic cylinder

El Salvador electric furnace hydraulic cylinder

(El Salvador electric furnace hydraulic cylinder,produced by Hengyu Group)

electric furnace hydraulic cylinder are widely used in El Salvador,because of no need for deceleration device,high work efficiency,excellent fatigue and impact resistance.So our company has designed electric furnace hydraulic cylinder for customers from El Salvador.

Introduction to electric furnace hydraulic cylinder:

electric furnace hydraulic cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the electric furnace hydraulic cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

The pressure of the sliding surface of the electric furnace hydraulic cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the electric furnace hydraulic cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

The definition of the minimum starting pressure of the electric furnace hydraulic cylinder refers to the minimum working pressure of the electric furnace hydraulic cylinder in the no-load state, which is a comprehensive index reflecting the manufacturing and assembly accuracy of the electric furnace hydraulic cylinder parts and the size of the sealing friction.

When the electric furnace hydraulic cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the electric furnace hydraulic cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil electric furnace hydraulic cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical electric furnace hydraulic cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the electric furnace hydraulic cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

Answers to some questions about electric furnace hydraulic cylinder:

How does the cylinder work?
Hydraulic transmission principle: oil as the working medium, through the change of the sealing volume to transfer movement, through the internal pressure of the oil to transfer power. 1. The power part - converts the mechanical energy of the prime mover into the pressure energy of the oil (hydraulic energy). For example: hydraulic pump. 2, the executive part - the hydraulic pump input oil pressure energy into the mechanical energy to drive the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3, the control part - used to control and adjust the oil pressure, flow and flow direction. For example: pressure control valve, flow control valve and direction control valve. 4, the auxiliary part - the first three parts are connected together to form a system, which plays the role of oil storage, filtration, measurement and sealing.

What is the thin cylinder used for?
The principle is no different from ordinary cylinders, that is, the installation space is small, the formation is small, and it is suitable for some special occasions. For example, the space is compact and the place of small travel is used.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP